/************************************************************************ ** ** ** ULTRA ELECTRONICS CARD SYSTEMS ** ** ** ************************************************************************* ** ** ** PROJECT : Magicard Avalon Firmware ** ** ** ** MODULE NAME : Amendment Record ** ** ** ** ** ** SIN No. : Sin 1977 ** ** ** ** COPYRIGHT : Ultra Electronics Card Systems ** ** ** ************************************************************************* ** AMENDMENT RECORD ** ************************************************************************* ************************************************************************ DATE DCR VERSION 21-8-07 29822 V2.03 1.Corrected problem when checking for a gap between the cyan and the black panels when using lc1 film. ************************************************************************ DATE DCR VERSION 10-1-06 28972 V2.02 1. Fixed bug which hung the printer after internal test pattern. 2. Ensured correct cam position on Power up or Lid closing reset. ************************************************************************ DATE DCR VERSION 10-1-06 28957 V2.01 1. Added ability to set Product ID. ************************************************************************* DATE DCR VERSION 23-11-05 28905 V2.00 1. Made default serial number 123456. 2. When the flash memory is upgraded with a bigger strucutre then already exists the user settings are now retained. 3. Undid v1.03 mod 'Correction to allow multiple (batch) prints within one print job.' This may possibly be causing the Avalon to go offline. ************************************************************************* DATE DCR VERSION 11-10-05 28834 V1.07 1. Fixed LC3 out of dye film problem. ************************************************************************* DATE DCR VERSION 18-08-05 28733 V1.06 1. Fixed problem whereby the Smart Encoding positioning commands such as GEM was occasionally extracted from track 1 encoding data e.g GEMMA. ************************************************************************* DATE DCR VERSION 20/7/05 28753 V1.05 1. Corrected the error that intermittently occurs when the printer is powered up with the lid open. Closing the lid does not always re-initialise the printer. 2. Improved Dye Film Barcode reading reliability. 3. Added MMM command for magnetic encoding testing. 4. Slight improvement to Magnetic Encoding quality. 5. Added SHW command facility to individually test each of the 8 sensors. using the Magicard Support Utility -> General Utilities -> Quick Commands function the following commands will run the indivial tests. SHWCAM1 - The cam motor runs continually whilst the green front panel LED reflects the status of the rear cam sensor. SHWCAM2 - The cam motor runs continually whilst the green front panel LED reflects the status of the front cam sensor. SHWTACHO - The green front panel LED reflects the Tacho sensor status whilst all motors remain off and lid switch is ignored. SHWDYE - The green front panel reflects the Dye Film sensor status whilst all motors remain off and lid switch is ignored. SHWBARCODE - The green front panel reflects the barcode sensor status whilst all motors remain off and Lid switch is ignored. SHWLID - The green front panel reflects the status of the lid switch whilst all motors remain off. The green LED will be on if the lid is closed. SHWFRONT - The green front panel reflects the front card sensor status whilst all motors remain off and lid switch is ignored. SHWREAR - The green front panel reflects the rear card sensor status whilst all motors remain off and lid switch is ignored. Note that for all opto-sensor tests the green LED will be ON when the sensor is not obscured. Note also that when sending a SHW command that the green LED will flash a couple of times before displaying the sensor status. SHWOFF - This command will return the printer back to the standby state. 6. Added Sensor test routine for production testing. Using the Magicard Support Utility -> General Utilities -> Quick Commands, send SNS. This will run a full test routine and display the results via the status monitor. 7. Resolved inability to magnetic encode only which has occurred since v1.03. 8. Included RAMP adjustment improvements. 9. Corrected the internal test pattern with AV1 film, it will now print the colour test also. ************************************************************************* DATE DCR VERSION 25/05/05 28660 V1.04 1. Fixed bug in the cam operation during mag encode/verify. ************************************************************************* DATE DCR VERSION 01/12/04 28344 V1.03 1. Modified card eject routine to ensure the card always clears the sensor. 2. Correction to allow multiple (batch) prints within one print job. ************************************************************************* DATE DCR VERSION 11/10/04 28281 V1.02 1. Resolved dye film mispositioning on a brand new roll. ************************************************************************* DATE DCR VERSION 19/09/04 28254 V1.01 1. Improved dye film positional calibration to improve registration while mag encoding and batch printing. 2. Modified dye take-up to improve image quality. 3. Fixed holopatch bug if HPH command received. ************************************************************************* DATE DCR VERSION 8/9/04 28112 V1.00 1. Initial release.